Frequently Asked Questions

How fast does it edge?

The BedShaper edges up to 100′ per minute; it makes short work of your largest edging projects. You’ll create clean, sharp edges, even “S” curves, at up to 100′ per minute. With these speeds, you’ll cut your labor costs almost as fast as you’ll cut the most intricate shapes!

Competitive machines typically can only edge 10′ per minute.

How deep will it cut?

Depth is controlled by a 9-position, easily adjustable gauge wheel. You’ll achieve cutting depths from .5 inches to 4.5 inches.

What makes the BedShaper edge better than competitors in its class?

The powerful notched blade slices through the soil and turf to create a clean, sharp edge – and the blade is GUARANTEED FOR A LIFETIME against chipping, breaking, bending, and delaminating. When the notched blade contacts a rock or tree, BladeFloat™ lets the arm ‘float’ over the obstruction while the blade continues to cut.

The ShapeTrak™ design mounts the blade in-line with the drive wheels; the blade follows the exact path of the wheels for precise edging.

Uneven terrain is no problem with its hydrostatic transmission.

Edging around trees is fast due to the BedShaper’s zero-turning radius.

What is the warranty on the Little Wonder BedShaper?

The Little Wonder BedShaper® is guaranteed against defects in material and workmanship for a period of TWO YEARS from date of purchase, when used for CONSUMER SERVICE or COMMERCIAL SERVICE. Any Little Wonder BedShaper® or part found to be defective within the warranty period is to be returned to any registered Little Wonder dealer.

Engines for all gasoline powered products are warranted separately by the engine manufacturer. Therefore, there are no warranties made, expressed or implied, for engines for gasoline powered products by Little Wonder.

What oil is used in the transmission?

Regular motor oil (20W-50)

I burnt out my 18202 drive belts, is there anything I can do to prevent this?

Yes, install one Part No. 22172 belt in place of the two Part No. 18202 belts, and train the operator not to start the machine with the blade in the ground.

How can I control the depth of cut on the go while edging sand traps.

Install the Part No. 80004 golf course quadrant.

My machine arrived with the hydrostatic transmission oil below the add mark on the oil expansion tank.

That mark is not an add mark, but is a cold mark. As long as there is some oil in the expansion tank, the level is fine.

What are the maintenance requirements of the transmission, gearbox, and differential?

None. The oil does not need to be checked or changed – ever because they are sealed systems.

How long will a blade last?

Typically, the blade can edge about 10 miles of bed. Wet soil will wear the blade less; dry soil will wear the blade more.

Can I adjust the angle of the cutting blade?

No, it is fixed. What looks like an adjusting rod is really a stabilizing rod to absorb the trust loads coming from the soil.

Why should I choose a Little Wonder Blower?

Little Wonder Optimax Blowers feature a patented discharge system which moves debris at the top AND the bottom of the pile. This system allows the operator to change air direction without tools. The patented split orifice deflector eliminates “blowback” or windrowing. Our computer-designed impeller enables our blowers to move more air. Little Wonder Optimax Blower units have three large pneumatic tires for easier maneuverability, even on rough and uneven ground. Our blower housing seams are arc welded robotically, which results in no air leakage. And our scrolled housing enables our blowers to generate more air.

Best of all, Little Wonder Optimax Blowers are backed by an industry-leading five-year warranty against defects in material and workmanship. Engines are warranted separately by the engine manufacturer.

What is the benefit of split discharge?

This patented feature allows you to blow the top AND bottom of a pile of leaves at the same time – eliminating debris blow-back onto the operator.

What are CFM’s?

CFM’s (cubic feet per minute) are the volume of air produced and combined with the speed (miles per hour) these numbers describe a key part of blower performance. High speed helps to lift material, and high air volume moves material along. Control of that airflow is a Little Wonder advantage and what makes our blowers more productive for you! The volume and velocity vary by blower model. See the blower Model Chart for all specifications by model.

What are the benefits of pneumatic tires?

Pneumatic tires last longer than semi-pneumatic or solid caster tires. It is much easier to push on wet and soft surfaces, particularly turf. It makes moving over curbs much easier.

What are the benefits of the Swivel Wheel Kit?

The Swivel Wheel reduces operator fatigue and makes the blower easier to turn and handle. The swivel wheel can be locked into straight position for stability on slopes. The Swivel Wheel Kit will fit most models of Little Wonder Blowers.

What type of gas is used?

We recommend using unleaded 89 octane or higher.

How much does the gas tank hold?

Please see the Model Chart page for complete information.

What type of paint is used?

Surfaces are powder-coated for extreme durability.

What is the warranty on Little Wonder blowers?

All Little Wonder Optimax Blowers are backed by an industry-leading five year warranty against defects in material and workmanship. The engines are warranted separately by the engine manufacturer.

How do you remove the fan?

Refer to your Owners Manual. This procedure should be done by an authorized Little Wonder dealer.

Are engines shipped with oil in them?

No, Little Wonder Blower units are not shipped with oil in them.

Can you overfill the oil?

Yes. If you overfill the engine with oil, it will blow white smoke and oil will come out of muffler.

Why should I choose a Little Wonder Electric Hedge Trimmer?

Little Wonder Electric Hedge Trimmers are lightweight and powerful, with features that are designed to increase productivity. They are quiet and environmentally friendly. The Little Wonder brand is dominant in rental trade.

What are the amps?

Our new electric hedge trimmers are 4.5 amps. See the Models Chart in the Electric Hedge Trimmer section of our web site for more details.

What thickness of a branch can be cut?

Little Wonder electric hedge trimmers will cut up to ½” (13mm).

What does it weigh?

Little Wonder Electric Hedge Trimmers weigh from 7.6 lbs. to 10.1 lbs. See the Models Chart in the Electric Hedge Trimmer section of our web site for more details.

What are the blades made of?

Considered by professionals to be the best blades in the world, they’re made with through-hardened tool steel.

What is the warranty on Little Wonder Electric Hedge Trimmers?

2 years consumer / 1 year commercial.

What gauge of electric cord should be used with Little Wonder Electric Hedge Trimmers?

For cord length up to 100 ft, we recommend 16 gauge.
For cord length up to 200 ft, we recommend 14 gauge.

What maximum length of extension cord can be used before losing power?

100ft. If more than 1 cord is used, expect a loss of 5 watts per connection.

How do you operate the Little Wonder Electric Hedge Trimmer without cutting the cord?

Loop the electric cord through your belt on the right or left side of your pants. Leave only enough cord from the trimmer to the front of the loop – it will to allow you to reach out with the trimmer.
This will help reduce the risk of cutting the cord.
Additionally, the cord retention system on our new Electric Hedge Trimmers prevents the extension cord from disconnecting.

My Little Wonder Electric Trimmer seems to be running slower than when first purchased; what could be wrong?

1) Check for sap build-up on the blades. To remove sap build-up, soak the blades in #10 light oil.

2) Check all adjustment screws on the blade. Refer to FAQ “How do you adjust blades” for Instructions.

3) Check for splices in the electric cord. Each splice increases electrical resistance and reduces the efficiency of the unit. Replace a spliced cord with a new cord and the blade speed will run like new.

How do you sharpen blades?

Recommend it to be done by a professional. Blades must be removed to sharpen and must be sharpened on a 38º angle by sander or sharpening stone. Do not sharpen the flat side of the blade.

How do you remove sap build up on blades?

We recommend using only #10 light oil.

How do you adjust blades?

1) Place trimmer in vise, clamping on the frame bar. Be careful; the blades are sharp!
2) Use a 7/16″ wrench, loosen all blade locknuts and unscrew large head screws by two turns.
3) Starting with screw nearest gear housing, tighten screw until blade guard of Single Edged trimmer or the protective comb of the Double Edged trimmer can just be moved with finger pressure and a .0015″ (1 ½ thou.) feeler blade just slips under the blade guard or comb. Tighten locknuts while holding screw stationary in its correct adjusted position
4) Repeat Step 3 on screws in turn, until all are correctly adjusted.
Note: Correct blade adjustment can only be achieved on clean, oiled blades.

What oil is recommended for blades?

We recommend using #10 light oil.

Why should I choose a Little Wonder Gas Hedge Trimmer?

Little Wonder Gas Hedge Trimmers are a superb value. Our blades are through hardened…the best blades on the market. They’re warranted with a five year consumer/commercial warranty on bar, blades, gears, gearbox and handle. One year consumer/commercial warranty on engine.

What does it weigh?

Little Wonder Gas Hedge Trimmers weigh from 11.7 pounds to 13.5 pounds. We reduced the weight by up to 10%. See the Models Chart in the Gas Hedge Trimmer section of our web site.

What size of branch can be cut?

Little Wonder Gas Hedge Trimmers will cut up to 1″.

What are the blades made of?

Considered by professionals to be the best blades in the world, they’re made with through-hardened tool steel. Blades keep their edge longer, which translates to less downtime for sharpening.

What is the gas and oil ratio?

The ratio is 50:1. Use high quality 2-cycle air cooled engine oil.

What is the warranty on Little Wonder Gas Hedge Trimmers?

Little Wonder Gas Hedge Trimmers come with a five year warranty on bar, blades, gears, gearbox and handle, and a one year warranty on the engine.

How do you hold a single-sided Little Wonder Gas Hedge Trimmer?

The operator holds the unit so they are behind blade with cutting teeth facing away from operator, placing their right hand on the front handle and left hand on the rear handle.

How do you sharpen blades?

Recommend it to be done by a professional. Blades must be removed to sharpen and must be sharpened on a 38º angle by sander or sharpening stone. Do not sharpen the flat side of the blade.

How do you remove sap build up on blades?

We recommend using only #10 light oil.

How do you adjust blades?

1) Place trimmer in vise, clamping on the frame bar. Be careful; the blades are sharp!
2) Use a 7/16″ wrench, loosen all blade locknuts and unscrew large head screws by two turns.
3) Starting with screw nearest gear housing, tighten screw until blade guard of Single Edged trimmer or the protective comb of the Double Edged trimmer can just be moved with finger pressure and a .0015″ (1 ½ thou.) feeler blade just slips under the blade guard or comb. Tighten locknuts while holding screw stationary in its correct adjusted position
4) Repeat Step 3 on screws in turn, until all are correctly adjusted.
Note: Correct blade adjustment can only be achieved on clean, oiled blades.

What oil is recommended for blades?

We recommend using only #10 light oil.

How do you grease a Little Wonder Gas Hedge Trimmer?

Remove the cover from the bottom of the gear case. Then fill the gear case ¾ full.

How do I remove gas trimmer engine to put on the Mantis Tiller/Cultivator, Mantis Edger or the Mantis Hedge Trimmer attachment?

Disconnect the ground wires from the engine, remove the air cleaner cover and disconnect throttle, loosen bolt at the base of the unit and slip the engine off. Reverse this procedure to place the unit on other attachment.

Where can I find a dealer that sells Little Wonder or Mantis products?

Click on the Dealer Locator icon on this web site to locate the dealers in your area.

I need a part for my Little Wonder product; who do I contact?

If you know the part number, please contact your Little Wonder dealer. If you don’t know the part number, contact our Customer Service Department.

What is the capacity of the debris collection bag?

The easy-empty bag holds 8 bushels of debris; it takes just a second or two to reattach the bag to the unit.

Is there a liner kit available for the housing?

There is a replacement liner kit available for the Pro Vacuum Model 5610. The part number for the kit is Product No. 600025. The Pro Vacuum Model 5600 does not have a replaceable liner, and it cannot be retrofitted with one.

Will the Little Wonder Pro Vacuum pick up parking lot debris?

Yes, it will pick up general litter — including paper, cans, bottles, cigarette butts, etc.

Can the Pro Vac pick up yard debris?

Yes, it will pick up general yard debris including grass clippings, leaves, small branches, acorns, chestnuts, sweetgum balls, small stones, etc.

How often should I change the engine oil on the Little Wonder Pro Vacuum?

Please consult the engine owners’ manual.

How often should I clean the air filter?

Please consult the engine owners’ manual. You may prefer to clean the air filter regularly, due to the dusty conditions under which the Pro performs.

Can I line the existing mesh bag with a trashcan liner?

No. The plastic bag would restrict the airflow, thereby reducing the suction.

How much weight can the bag hold?

The debris collection bag will hold up to 90 pounds.

Does the Little Wonder Pro Vacuum reduce the material as it vacuums?

Yes it does; the drier the material the greater the reduction.

Why should I choose a Little Wonder Lawn Edger?

Little Wonder Lawn Edgers are a great value! Throttle, depth of cut, and blade engagement controls are all independent of each other. Our Lawn Edgers feature a solid steel frame. Our solid steel axles and steel-hubbed wheels are more durable and distribute stress for longer unit life. Little Wonder Lawn Edgers are available with a diverse selection of engine options. With our Pro models two belts transfer all of the engine power to the blade, reducing the risk of belt slippage.

What size belt is used?

Belt size is ½” X 30″. Little Wonder part #177. Gates part # 2300.

What kind of grease is used in cutter head?

Lithium 0 grease is used in the cutter head.

What is blade made of?

Hardened steel.

What is the blade size?

The blade on our Little Wonder Lawn Edgers is 10″ X 2″.

How wide a blade can be used on a Little Wonder Edger?

Single belt units – one blade width or one blade.
Dual belt units – two blade widths, however you can expect more belt wear.

What is the warranty on Little Wonder Lawn Edgers?

Little Wonder Lawn Edgers are warranted 1 year for consumer use / 90 days for commercial use.

Why is the belt fraying?

Fraying may be due to burs on the pulley or abuse by dropping the blade more than 2 inches in the ground at one time on the first edging pass.

To the remove blade, are the threads on shaft right- or left-handed?

The threads on the shaft are right-handed.

How much oil is needed to fill engine?

Oil capacity is 16 oz. You cannot overfill because oil will come out of fill hole.

How should the mud flap be positioned?

Mud flap should be positioned at a 45º angle toward the blade.

How do you change the belt?

You will need a 3/8″ socket and ½” wrench. Remove the guard and slide belts off the pulley. Put on the belt closest to the engine first (if your unit has two belts), then add the other belt. Install the guard.

How is the depth controlled and how deep can blade go when beginning to edge?

The blade should not go below 2″ into the ground on the first pass when starting a new edge. Little Wonder Edgers have a lever on the handle that controls depth by adjusting the position of the front wheel. This unique feature keeps constant tension on the belt and reduces risk of belt slippage.

Do I need to mix oil into the gas?

Little Wonder Lawn Edgers are powered by 4-cycle engines. 4-cycle engines do not require that oil be mixed into the gasoline.

What type of gas should I use?

Use gas that is unleaded 89 octane or higher.